Sanyo RCS-KS2432AWD Manuel d'utilisateur télécharger pdf

■ Parts supplied with remote controller

See Table 1.

■ Remote controller installation guidelines

• Mount the remote controller 1 to 1.5 meters off the

floor where it can sense the average temperature of

the room.

• Do not mount the remote controller in a place

exposed to direct sunlight or where it is exposed to

outside air such as near a window.

• Do not mount the remote controller behind a curtain

or other object so that it is separated from the air cir-

culation of the room.

• Mount the remote controller inside the room being air

conditioned.

• The remote controller should be mounted on a wall or

other surface vertically.

Room temperature sensors are separately incorporated

in both the indoor unit and the remote controller. Either

sensor can be used to sense the room temperature. The

indoor unit sensor is usually used.

If you wish the remote controller to sense the room tem-

perature, press the SENSOR button with a ballpoint pen

or tool with a small tip.

■ How to install the remote controller

<NOTE 1> Do not twist the remote controller wire

with the power cord, or run them in the

same metal conduit, because this may

cause a malfunction.

<NOTE 2> Install the remote controller away from all

sources of electrical noise.

<NOTE 3> Install a noise filter or take other appro-

priate action if electrical noise affects the

power supply circuit of the unit.

• Use an electric junction box (supplied locally) for

embedded mounting of the remote controller.

(See Fig. 1)

Switching the room temperature sensor

Installation location

Q’tyNo.

➀ 1

Supplied parts

Remote

controller

(comes with

200mm wire)

Machine screws

M4 × 25

Tapping screws

M4 × 25

➁

➂

Q’tyNo.

➃ 2

Supplied parts

Spacers

Wire joints

Harness

Clamper

Instruction manual

➄

➅

➆

➇

Table 1

Note: Remote controller model name RCS-KS2432AWD

Code: 851-0-0054-590-00-0

INSTALLATION INSTRUCTIONS

Fig. 1

Wall

Under-case (back case)

Electric junction box

(no cover)

Spacers

Remote controller

Lead wires (3)

Machine screws

M4 × 25 (2)

RCS-KS2432AWD

03-242.Sanyo.85464359404000 8/21/03 9:17 AM Page 1

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Parts supplied with remote controllerSee Table 1. Remote controller installation guidelines• Mount the remote controller 1 to 1.5 meters off theflo

Page 2 - Approx. 200mm

2• For surface mounting on the wall, see Fig. 2.1. Insert a screwdriver or the like in the groove on thelower side of the remote controller to pry off

Page 3 - • Electric Wiring Diagram

3Fig. 5876543218765432112345123451234512345FLPCONNECTORFLAP25P [BLK]FLAP15P [WHT]LAMP 4P [WHT]RECEIVER 3P [WHT]SEC2P [WHT]PRY3P [RED]SUP5P [WHT]ROOM/

Page 4 - INDOOR UNIT

4Fig. 7OPERATIONTIMERONOFFTESTINDOOR UNITOPERATION lampOperation selectorRemote controlreceiverTIMER lamp How to test run the air conditioner1. Switc

Commentaires sur ces manuels

Pas de commentaire

Sanyo RCS-KS2432AWD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Climatiseurs mobiles Sanyo RCS-KS2432AWD. Sanyo RCS-KS2432AWD User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Climatiseurs mobiles Sanyo RCS-KS2432AWD